JUMP AROUND CODE
JUMP AROUND ISO
JUMP AROUND PLUS
JUMP AROUND TV

If you have macro you can do a similar thing on Mazak, Haas or Fanuc. N100 N100 (ARRIVE HERE) Without Fancy Shit (Just jump some code) This is how you do it on a Toshiba (the blue bit).ДonвЂ™t forget itвЂ™s GO (thatвЂ™s G and letter O) not G0 which is G and number zero (Rapid Command).ДonвЂ™t get your letter OвЂ™s and your number zeros mixed up.

JUMP AROUND CODE

Jumping Sections of Code on a Toshiba Tosnuc 888 or Similar In MDI Type in #1=6 if you have macro it will work if you donвЂ™t youвЂ™ll get an alarm and your machine will self destruct in 15 minutes. To do this you must have the Macro Option if you donвЂ™t then this is where M99 comes in handy.Д«est way to see if you have macro is to try using it in MDI. Yes you can do this with GOTO This is my pet Cockroach his name is Boris Just read through it a few times and the penny will drop.

JUMP AROUND TV

Sorry IвЂ™m losing my temper a bit here, the dogвЂ™s just pissed on the TV remote again. WhatвЂ™s the matter with you lot just take some time to fuckin read it. Now I know this is a bit confusing and maybe I didnвЂ™t explain it too well.

JUMP AROUND PLUS

The Clever Shit (M99 Plus Block Skip) WhatвЂ™s This? Meaning it runs as normal not jumping any tools. The first thing it will do is jump over the bit that tells it to jump the code. In the example below if the block skip is off, which it will be when you start up your machine. The default should really be the way the programme was originally done. My way of looking at it, is that you would want the default to be running the whole program as normal. That means the default would be to jump the code. Most machines now donвЂ™t have a mechanical switch for BLOCK DELETE/BLOCK SKIP so when you turn on the machine block skip will always be off. Call me finicky but I like the BLOCK SKIP/BLOCK DELETE as a default to be off. However, see the next Example.ДЇor this last example you might have to think a bit. In this case IвЂ™d just jump with M99 and then take it out before saving the program. Maybe you broke all the taps and you donвЂ™t have anymore so you want to skip the tapping. If you temporarily want to skip a section of code.Д«e careful what N Numbers you choose so as not to mix them up. If you put the BLOCK SKIP/BLOCK DELETE on it will not jump the spot drill. The P part is the N number you want to jump to. In the case below it tells the control to jump to N100 (M99 P100). You probably normally see an M99 at the end of a sub programme. Do You Have Adequate Life Insurance? M99 CNC Code (Now letвЂ™s use it) Some controls even have two three and four block skips so you can switch on any combination of these switches, mmmm complicated. If you want to skip a big section of code you will have to write in loads of block skips.Д¬all me a lazy bastard but I definitely couldnвЂ™t be arsed with that. It works ok but it is very time consuming. On most Fanuc controls itвЂ™s B.D.T not to be confused with CBT (Cock and balls torture) please do not google this in company time. When you switch on your BLOCK DELETE/BLOCK SKIP switch, each time a forward slash (/) is seen that block will not be processed and the control will move on to the next block. The programme above contains BLOCK SKIPS sometimes called BLOCK DELETES. You could delete it and make two programmes (sounds like hard work and loads of errors). In this example itвЂ™s a spot drill we want to miss out.

(If you want to do this on a Toshiba Tosnuc 888 or similar control go to the end of the article) Imagine you want to skip a complete section of program in the case below itвЂ™s the Spot Drill. Yes it means continue and is used at the end of a sub program. (Please in the name of holy shit do not call me Dave.) Now I know you are all thinking вЂњDave youвЂ™re wrong itвЂ™s the end of a sub-programвЂќ. Learn to use this in conjunction with the block skip command to switch it off and on.

JUMP AROUND ISO

M99 Plus Block Skip, M99 on a Fanuc, Haas or Mazatrol ISO control can be used to jump sections of code.

Jump around